Drag rods

...drag link, pitman arm, wheel bearings, brake lines, and shoes. A spare is mounted under the bed. The five-digit mechanical odometer indicates...

...drag links, and strut rod bushings. The seats were reupholstered in 2012, and a replacement headliner, carpeting, and door panels were also...

...rods and sleeves, idler arm, pitman arm, and hoses. The original rebuilt generator is also included. An AM/FM CD player was professionally...

...manifold and a four-barrel Holley 735-cfm carburetor. The engine came from the factory with a forged steel crankshaft, forged connecting rods...

1941 Chevy drag car. All steel body. Chopped 2 inches, sectioned 7 inches. Front end lengthened 3 inches. Rear body shortened 8 inches. Tilt...

For sale or trade 07 jeep wrangler x 4x4 6speed with 66000 miles. Runs good never had any issues with it besides tie-rods and drag link which...

...The J-code 429ci Super Cobra Jet V8 was the highest-spec Mustang engine available for 1971 and features forged pistons and connecting rods...

...differential. The 355ci V8 is bored. 030″ over and features a Lunati Voodoo camshaft and roller valvetrain, an Eagle forged crankshaft and rods...

...drag link in addition to performing an alignment. The front bucket seats and rear bench are recovered in Bamboo MB-Tex, and the tan carpets...

...drag link. A steel spare tire cover is included in the sale. The tan cloth upholstery was not replaced during the build, and the interior is...

...Air A/C. It also has a new 383 motor built by Skip White Performance that was installed in 2020, with Scat Forged Crank and Competition Rods...

...driveshaft, new race stars, 15x15 rear with 5.5 bs 216x8.5 hoosier slick, front is disc brakes with chevette front rack an pinion, 9010 drag...

...Hamtramck, Michigan, in October 1969. This is a real R-Code Hemi 'Cuda, it is a non-numbers matching block and transmission. The car has a drag...

...rods, Ross pistons. AFR aluminum Eliminator angle plug heads, Comp cams cam, Scorpion full-roller rocker arms. Air gap intake, 800 cfm carb...

...426 Hemi rebuilt top to bottom bored. 040 over about 600HP. 040 overbore Forged Venolia 10.5:1 pistons Lightened, polished, and shot peened rods...

1967 Camaro. I Purchased this car 11 years ago as a daily drivergot the racing bug converted into a full-fledged drag car. Aspictures show...

...vehicle runs great. 1968 Buick Skylark 462 ci Big block Buick (2 month old have all receipts and build photos). Ta performance sportsman rods...

...Drag Links, Etc Just Repacked Wheel Bearings New Ceramic Brake Pads Body & Interior Mods Complete 2007 Conversion 16 KMC Rockstar Wheels with...

1951 Mercury lead sled, built by Harts Hot Rods in Brea, Ca for 5 time NHRA drag racer Joe Amato, complete frame off build with extensive body...

355cui SBC, Rings 30 over, Clevite rods, mains, bearings, JE Pistons 30 over, Lunati 6in Rod, Solid lifter camshaft, 545 intake, 563 exhaust...

...rods, new lifters, pistons and cylinders. Rebuilt single port heads. 1968 spec carb and distributor. New alternator, belt, plugs, wires, cap...

...by listing much of the build here, but if you're looking toget into the racing scene, or to increase your stable, take a goodlook at this drag...

...rods w forged pistons (93 non-ethanol). Scat rotating assembly. Dart Iron eagle cylinder heads. Scorpion 1.7 and 1.8 ratio roller rockers...

...and low miles! Built on a Ford Super Duty F-53 Chassis which has been enhanced with Safe-T-Plus front and rear anti sway bars, track bars, drag...

...chevrolet nova 5.3 ls v8 engine with single 88mm precision turbo blow off and waste gate. Holley terminator ecu harness. And 7 screen eagle rods...